GOOD FLEXRADIO 3000 FLEX-3000 SDR HAM RADIO TRANSCEIVER

Description

30 day warranty
You get the pictured FlexRadio HAM Radio Transceiver and cables shown. You get the firewire and the power cable assembly.
(See my other related auctions too)
You need a 13.8V power supply, a computer with Flexradio type software and a display (all of which aren’t supplied) to operate this radio. This FlexRadio was from an operating system.
BACKGROUND INFO FROM FLEXRADIO:
.
The FLEX-3000 is a third generation software defined radio from FlexRadio Systems. It is a low cost/high performing HF-6M transceiver built with portability in mind. The FLEX-3000 form factor is designed to fit in a case along with a laptop and a power supply for mobile use or sit under a monitor at a base station. The FLEX-3000 utilizes high performance 24-bit A/D and D/A converters enabling superior close-in receiver performance. The FLEX-3000 offers greater than 93 dB Two-Tone 3rd order dynamic range at 2kHz spacing making it a higher performing radio than those costing two and three times as much. The small size makes it great for Excitement Anywhere!™. FlexRadio Systems is a leader in Software Defined Radio (SDR) technology. Our high-performance, PowerSDR™ software is the gold standard in SDR radio software.
SoftwareDefinedRadioTechnology• FullHF-6mcoverage• 100Wattclassradio• 96kHzreal-timereceivebandwidth• >93dbofTwo-Tone3rdorderdynamicrange• BuiltinAutomaticAntennaTuner• 12.2”X2.1”X12.4”• Only7lbs
General Specifications:Rx Frequency Range :10 kHz - 65 MHz (operating below 1.8 MHz requires external, customer provided filters to eliminate images)160 - 6 m (specified performance in Amateur bands only)Frequency Stability :±2.5 ppm TCXO std. 32 °F to 122 °F (0 °C to+50 °C)Optional ±0.5 ppm TCXOOperating Temperature Range :14 °F to 122 °F (–10 °C to +50 °C)Emission Modes :A1A (CW), A3E (AM), J3E (LSB,USB), F3E (FM),F1B** (RTTY), F1D** (PACKET), F2D**(PACKET)Frequency Steps :1Hz minimumAntenna Impedance :Antenna input: 50 Ohms nominal, unbalancedATU tuning range: Minimum 10-300 ohmsPower Consumption :Rx 1.5A (typ.); Tx (100 W) 25A(max.)Supply Voltage :DC: DC 11-15 V Negative GroundTransmitter output specified at 13.8VDCMaximum Interconnect Cable Length :Firewire - must comply with IEEE 1394a standardNo restriction on DC power cable within voltage tolerance limits under load.CE Compliance Cable Requirements :1 snap on ferrite bead on DC power cable (supplied)2 snap on ferrite beads on FireWire cable (supplied)1 snap on ferrite bead on FlexWire cableAll beads to be located adjacent to rear panel of radio.Dimensions :(WxHxD):12.2” X 2.1” X 12.4” (23.5cm x 22.1 cm x 31.6 cm)Weight: (approx.): 7 lbs (3.2 kg
Receiver Specifications:MDS :MDS (typ) @ 14 MHz, 500Hz BW Preamp      OFF            PRE1           PRE2              -121dBm      -126dBm      -135dBmIP3 :+28 dBm @ 14 MHz with preamp off at 2 kHz or less tone spacing (S5 IM3 method)Selectivity :(–6/–60 dB):CW 500 Hz –6/-60 dB: 500/640SSB 2.4 kHz –6/-60 dB: 2.39/2.54AM 6.6 kHz –6/-60 dB: 6.60/6.74Transmitter Specifications:Transmitter Frequency Range :160 - 6 m (Amateur bands only)Power Output :1 - 100 watts nominal PEP CW and SSB at 13.8VDC                input voltage25 watts nominal AM carrierEmission Modes Types :A1A (CWU, CWL), J3E (USB, LSB),A3E (AM), F3E(FM), DIGITAL(DIGU,DIGL)Harmonic Radiation :Better than –55 dB (160 - 10m Amateur bands)Better than –60 dB (6m Amateur band)SSB Carrier Suppression :At least 55 dB below peak outputUndesired Sideband Suppression :At least 55 dB below peak outputAudio Response (SSB) :Flat Response 20 Hz to 20 kHz,3-band or 10-band Software Equalizer3rd-order IMD :Better than –33 dB below PEP @14.2MHz 100 watts PEPMicrophone Impedance :600 Ohms
Paul